量具 Measuring Tools
; u9 `3 o3 P2 j0 q4 V5 Q板规 plate gauge 2 U' D' a5 B% y. n
比例规 proportional dividers " Z: ?/ O a! h2 O z
标准规 standard gauge 7 n9 \% ?: N% g9 `( y2 k3 O- Z
齿轮规 gear tooth gauge
; L: n/ |! B* k N2 s& |丁字尺 T-square
6 Q- h2 r( J2 A+ v分线规 divider;dividers 4 B) Y8 l6 h: V6 B9 L8 E( ?3 m
钢尺 steel rule
# A2 Q: z4 a- q: T1 O1 K工作量规 working gauge
, l8 n! W+ u# V5 G3 s厚薄规 feeler(gauge) 1 d- z2 `/ ?% h8 r9 t0 V+ a
角尺 angle square
% X6 c2 x7 P4 D. `5 \角规 angle gauge
! m+ y2 L: z7 N6 f: L- o金属卷尺 metallic tape 6 n: ^3 }3 D2 l! Z3 j1 P) O
卡尺 calipers;caliper
' u0 m6 r8 l% H3 a0 i刻度尺 graduation ruler - u; {2 J! [* j% H
块规 gauge(block)
) T! v/ _) V1 e8 l9 T5 c0 O9 A8 ~量规 gauge ) ?) p$ g3 e2 M1 X& t, ~" F( x( r
螺距规 screw pitch gauge 7 ?) r; |* a$ f+ L9 h4 }
螺纹千分尺 screw micrometer
+ x' @: \& U/ _! j0 ]8 L内径千分尺 micrometer inside caliper;inside micrometer 7 v% _7 T6 K) F8 K5 o' f- d
内卡钳 inside caliper
0 T9 }1 F7 ?, \/ M- x/ L4 T皮尺 tape(/measure)
4 j- r1 o: B2 T/ L; @平面规 surface gauge 3 p. |: U( B4 d, \. T0 |
千分表 dial indicator 3 v ?8 O* b9 B, K+ `( K% N
千分尺 micrometer
2 z" \5 a/ H3 d/ e! V' r5 {曲尺 carpenter’s square
/ L9 l4 y1 H$ {+ i: Z三角尺 set square
" ]& D% c+ J7 t$ K }% s深度千分尺 micrometer depth gauge; depth micrometer
c9 `3 r7 Q' Z4 `4 b9 O3 y. f椭圆规 ellipsograph
1 [5 @& v5 Z1 ?# H6 a- w& T; R外径千分尺 outside micrometer : i! e/ _6 P: U( O2 i
外卡钳 outside caliper
# B6 i& z7 Y8 l: @& \隙规 gap(/clearance) gauge
0 K9 n Q2 T p线规 wire gauge ; B: h T1 ?2 _: n" N s& w+ {
斜角规 bevel square 7 \$ S5 R$ @4 T0 [2 d
游标卡尺 vernier caliper , `7 |. L: G& O% q' H0 @" p
圆规 compasses ( ]" p s% H1 j, F$ Z
折尺 folding pocket measure(/ruler)
* @3 }9 s6 n2 R- _+ n0 m G直尺 straight edge
+ K- P) d( _# r, q: I9 r中心规 centre gauge
! N2 }: w0 ?( e% A% H9 m% f锥度规 taper gauge ) B0 ~' l5 A- E; J3 r
组合角尺 combination set
6 J# Q6 ]3 n) g: A可调的磁力架----Magnetic stand with fine adjustment 8 R) {) }6 B6 T
点接触杠杆千分表 ---Lever dial indicator point contact length
5 f {- S9 S0 S6 a/ ]4 O `1 O) {- k' l; s卡钳式内径千分尺－Internal quick caliper dial gauge * N+ N0 j- x: d3 ~" s( V
孔的轮廓量规－Bore profile gauge KT
$ d z% u" S$ M- W, V8 A; A磁性吸座－－Magnetic stand * H% W/ L. f+ x4 a1 R' ]5 ]
花岗岩平台（精度1极）Granite table, accuracy 1
0 r' V9 B- ^8 X" F: g+ r8 H* i外径千分尺标准棒 ――micrometer standard
8 h. n6 P! Q" }3 M# W. {; d+ g+ I装有T型槽的平台-Tenon and T-slot incl. installation |
发表于 2008-4-21 09:38:48
