美国的斜齿轮图纸的英文,谁能帮忙翻译下,不胜感激!

yang13564

1.
2 K& n, u) v/ `6 kQuality: ANSI/AGMA 2000-a88-q11, full depth, full fillet.

2.
4 A* d" [8 N4 x' `  g' qFOR LEAD, CROWN, AND PROFILE TOLERANCES SEE DWG 54773379

3.
CROWN DRIVEN GWAR ONLY

4.
  C. L/ ~- Q2 u; aNORMAL PRESSURE ANGLE 20”

5.
NORMAL DIAMETRAL PITCH 8

6.
NORMAL CIRAULAR PITCH 0.3927

7.
, q( N5 B* `/ M. j( `HELIX ANGLE:16.6011

8.
BACKLASH TO BE 0.996” TO 0.008” ON 6.9784” CENTERS

9.
; H  G6 A+ y# h/ C) tMATERIAL: AISI 8620

10.
. U1 [: w/ y1 J* Z' z! wCASE CARBURIZE TO 0.025” TO 0.040” EFFECTIVE FEPTH AFTER GRINDING AND HARDEN TO 57-61 RC, CORE HARDNESS
TO BE 25-40 RC.

11.
RETAINED A USTENITE – 5% MAXIMUM BY VISUAL INSPECTION.

12.
EACH GEAR DEAR SET TO BE BOXED SEPARATELY AS A SET AND EACH GEAR MARKED WITH THE SET PART NUMBER ON THE OUTSIDE. EACH GEAR TO HAVE P/N AND SUPPLIER INENTIFICATION STAMPED. EACH GEAR TO HAVE P/N AND SUPPLIER IDENTIFICATION SATAMPED OR ELECTRIC ACID ETCHED AS SHOWN, APPROX. TEXT HGT..25’.

13.
- E2 h. J7 l; N4 t3 c; N( L! y4 E3 }REMOVE ALL CHIPS FROM TAPPED HOLES.

NUMBER OF TEETH

HAND OF HELIX

LEAD OF HELIX

PIRTCH DIAMETER

BASE CIRCLE DIAMETER

ADDENDUM

WHOLE DEPTH

TRANSVERSE CIRCULAR

TOOTH THICKNESS WO/BL

NORMAL CIRCULAR

TOOTH THICKNESS WO/BL

yang13564

8 ~# S7 h& U0 |2 i! I* A没有人翻译,找到了资料,不知道对不对!望高手出来指正!
4 i- _$ N0 L; Q' Q; ~* x& X  a* y        齿轮制造标准和精度等级：ANSI/AGMA 2000-A88，精度12级，全深，全倒角。
5 `0 L* n0 ]8 F. L7 K: Q' r        齿向、齿形修缘和渐开线轮廓公差按54773379图纸规定。
' V! r1 E! K1 @8 Y; a        仅驱动齿轮鼓形修整。
$ e, y6 C5 U+ m# i  O  p- N; M        齿形压力角20º
1 C" _1 |7 x: K  w! ^4 |        节径DP=10
        齿距：0.3142
        螺旋角：15.9355º
        在齿轮啮合中心距5.5118”上，侧隙要求在0.006” ~0.010”之间。
        齿轮材料：AISI 8620
' j' {) P% [6 \# ?        渗碳层0.025”~0.040”有效深度，表面硬度为57~61Rc，芯部硬度25~40Rc。
        残余奥氏体最大5%目测检查。
/ Q4 e7 Q3 ?% u3 p( Q        每个周转盒内只能装一个齿轮组，周转盒外标记齿轮组图号，齿轮表面须按图示部位用电蚀法标记零件号和供货商代码，字高约0.25。
        攻丝后，去除螺纹孔内的铁屑。

qvzhiwei

楼上玩意的好专业，佩服！！！

another

二楼挺专业的···感觉还不错，很值得学习。