|
|
楼主 |
发表于 2013-7-3 12:06:42
|
显示全部楼层
本帖最后由 宁波EN深孔加工 于 2013-7-3 12:07 编辑
! r8 ~) ~9 E8 w9 C
& _/ e% L* G8 Y1 @+ OO9300([A-00]GUN DRILL DRILLING CYCLE)
i( b) C# V: F( g4 T$ E( EIF[#9EQ#0]GOTO9001/ x2 E. S7 }* k) d7 u) }
IF[#18EQ#0]GOTO9001" \3 d" L6 S! U8 p0 J
IF[#20EQ#0]GOTO90016 h* o1 G8 ^. {, K. O+ E1 v% u1 L
IF[#26EQ#0]GOTO9001
, C. A( j+ c; i; q$ cIF[#26GE#18]GOTO9004* @! a; B# G# u: R) m5 E
IF[#20LT0.]GOTO9004( T3 O6 d! ~) D1 [5 ]- b' m- p! U8 W- [
IF[#20GT1.]GOTO9004
/ M8 x; C9 o" T5 Y4 ?$ ^#1=#5003
( k3 [+ W; x1 _* O( w: ~- B: tIF[#20NE1.]GOTO1000# m2 v# p. T3 X9 c% G6 N
G90G0W#5002
; k/ ~/ [0 e8 q1 E# X4 TG4X1.
9 G6 o! x+ b5 ZN1000 t8 ]7 S7 z8 t) `4 M8 G
M10% [5 q1 c1 \# L7 _
G4X1.7 k8 S0 o8 w1 q
M8
+ I! q3 a' m3 [* I; iM34 K$ s/ c% r! ~
G1Z#18F500
2 m$ o( |# O6 B0 I' D! C1 E% |Z0.5F50.
, m# i9 J- d2 }9 x$ E! @IF[#26GT[-8]]GOTO2000, a* ^4 Y F- l2 s) ]
Z[-5.]F[#9*0.2]
, G7 F' j, b% eZ[-5.5]F[#9*0.3]
; |/ f! G( R% R2 uZ[-6.]F[#9*0.4]
; Q8 j' Z3 l5 Z# A& U. O, HZ[-6.]5F[#9*0.5]
7 H) R# M* |% B& Y( m2 I$ |, YZ[-7.]F[#9*0.6]
6 b( X7 G/ }2 o4 `Z[-8.]F[#9*0.7]
* S2 Y& v. a" e+ I, [' y: NZ[-9.]F[#9*0.8]) Z$ t2 ~) E U: G* K1 Z8 L
Z[-10.]F[#9*0.9]
* r0 r# P/ O! s0 oN2000
9 G6 l5 D( |/ S2 t1 Q8 cG1Z#26F#9
! J: G+ r: w9 kM5# z; f- @, d7 V4 R0 o
M99 y* c" M6 O$ p9 X7 q$ j
G4X2
4 f1 a1 p& g5 K. ]' LG0Z#1
3 d6 \6 e I0 h( m( @ nM11
& l3 _; c) y& X2 d8 a' eG4X10 @( c2 J( W! H+ H5 D* g
M99
4 J3 c+ O5 E( |+ ~3 @4 A- S' |4 nN9001
5 X: L7 Y0 O: |" ^, V8 }' ?#3000=1(ARGUMENT HAD NOT BEEN SPECIFIED)
# p6 C, w4 G9 {8 V, yN9004
* a% s. G0 \- g) B9 [7 O9 n- |#3000=4(UNSUITABLE RANGE/CYCLE DEFINED)- ?" b( {( a2 p6 |3 k
) o* j" |0 S( t2 a7 R/ V$ Z
9300宏程序 |
|
发表于 2013-7-2 13:16:52
