回转类零件,车床加工效率高6 e1 x: B& r" R) g+ y5 b
椭圆加工宏程序
0 L; t2 U9 d" J& X0 ^7 w; l8 XO0123
$ i: Q1 y7 j. C. C/ W( t# B# TG50 X100 Z50 ' s8 k6 e' R0 o& P: L5 S4 \
S800 M3
( n }6 a- Z: F' e) z; d0 ]$ DT0101
}( n* `8 j, p$ HG0 X30 Z2' }! u' h- C8 t e& W7 I$ n. {& \# p
G95 G90 X28.5 Z70 F0.18
8 P2 Q! s6 \$ w$ A: B2 ^0 I E#1=28
) H0 x1 a5 J7 Z7 `#2=0 2 x/ D1 `% Z* u. K3 \) f
WHILE [#1 GE 0] DO 1
! W# }# g, }7 P* z4 cG0 X[#1]
3 R, u7 b4 E: C9 d% AG95 G1 Z[[#220] F0.18
2 A q! B6 t% J! I( M, WG0 U1
+ t, E$ @# h" f5 W9 N, OG0 Z2! Z- ^ w$ ^* {
#1=#120 o I1 W$ B3 M4 t$ L, z v
#2=20/28*SQRT[28*28#1*#1]
' q! X+ m7 r i# {1 MEND 17 q' f& J3 ^: t8 C7 L/ E
G0 X100 Z50 M5
! ~, k* S* a: P0 s$ v2 f+ K# BT0202 (切断刀刀宽3.2，左刀尖)' i3 |# e4 `2 W, V
M3 S400
: a* ?2 N$ Z) T8 Y( Z& R( K$ lG0 X32 Z45
. Z9 f9 E# i2 R5 @' `( F) mG94 X14 Z45 F0.10
! g t m! `7 [2 EX14 Z42
- Y0 p& s2 k! l3 k, R6 YX14 Z40.5219 W/ n5 _; X+ E& H, \2 `
G0 X32 Z40.5216 K, E$ M% |; [" e/ g% b3 W
#1=14- o: @" `, g' e5 |7 {! E- L
#2=17.321
& V; {9 |' @6 k. TWHILE [#2 LE 0] DO 1
. `5 ^& _& i- n8 u% r, |( w# F! xG0 Z[[#2]20]" W5 h h2 N* n8 X1 U) a7 p
G1 X[#1]/ d. s }7 P1 Q) A, M, g
G0 W1 D7 b& _2 x+ ^7 n
G0 X32) m& F1 m& M' J" K: ^$ u+ \7 F0 Y
#2=#2+3
3 G/ }; H( F: W0 Q0 w#1=28/20*SQRT[20*20#2*#2]
+ q' Y* M) \$ z( N c; X: Z$ q8 KEND 1
- ]# R& V* k) S5 \G0 X100 Z50 M5
9 E7 m ]" R* ? S' ]4 ~T0101 (35°尖刀)
/ Z o+ q* e0 |. I% z; x% \) `M3 S10003 ]0 S7 f& E/ y' {/ `% i9 I w+ K/ ]
G0 X0 Z3/ v5 {& x& p- m+ D' }* w, Q
G1 X0 Z0 G41( n' B1 \/ @ p6 C; S, F! f- |
#1=0+ O3 R6 A1 K4 M( H
#2=203 }7 Z0 w% z% @# V* s- e0 o0 q% y
X14 Z42* g$ O6 @! X: W; |
X14 Z40.521
$ U: ]0 g4 W3 d2 O* Y* b0 Z& LG0 X32 Z40.521, I( P6 d" P8 v* P4 B
#1=14
9 N1 M' k/ m0 q5 p% ]" |2 H+ P* ]#2=17.321
, [5 S, \8 G* ?0 y, DWHILE [#2 LE 0] DO 1
9 A* U% l& S' C$ n9 o+ u8 p0 \, ~G0 Z[[#2]20]5 E3 t4 d; K2 u
G1 X[#1]- A, Y' I2 A# S& R1 M
G0 W1 O5 q& b# P: ]8 N
G0 X32
. s3 Z1 f: I7 S+ U1 i. {, `#2=#2+39 r5 G( d4 s3 S, d# l" B
#1=28/20*SQRT[20*20#2*#2]
, p5 Z) `% q5 _2 cEND 1
2 j8 O! `! y0 n) N8 b" B# EG0 X100 Z50 M53 v! Z" F6 w T
T0101 (35°尖刀)
0 i9 r+ x% B3 |) pM3 S1000; r% P. {. a) \7 o
G0 X0 Z3
2 J& @ J q( o+ q+ aG1 X0 Z0 G41$ h9 I: A" n5 L. \
#1=02 ^9 b9 ?, L/ A0 \; C; k
#2=20
7 _3 \0 ~; \! O0 b/ n- S. L! P [) `0 F+ g2 R
|
发表于 2011-5-17 16:33:24
